Throughout September, get £10 off each BM4 & BR4 Leister igniter. Offer ends 30th September. Use code: LEISTER10. Dismiss
EX VAT
INC VAT
LoCO2 Heat are pre-insulated pipe and district heating specialists, and have direct relationships with the following pipe suppliers; Rehau, Uponor and CPV in Pex, copper and stainless steel.
We specialise in the supply of underground pre-insulated pipe and fittings for heat distribution and cooling networks. It also commonly gets referred to as underground heat main or district heating pipe, but whatever you decide to call it, we supply it.
District heating networks are the most common use for pre-insulated pipe. This is essentially where a single centralised heat source such as a biomass boiler, is used to heat multiple buildings as opposed to using single boilers in each. Here, pre-insulated pipe is used to connect the single heat source to multiple buildings to provide all the heat and hot water requirements. District heating networks have become increasingly popular, with many new build estates heated via this sort of network as not only can the capital cost overall be less, but it is considered a more efficient way of heating buildings so lowers operation cost and helps minimise carbon emissions.
Showing 97–112 of 258 results
Rehau 63mm+63mm/180mm Duo Lead in Bend The Rehau pre-fabricated lead-in bends enable the creation of tensionless wall entries that are bent up to 90 degrees to the piping. To be used with Rauthermex and Rauvitherm pipe. Connect other pipes using the standard I-shroud connection.
Rehau 75mm/160mm Uno Lead in Bend The Rehau pre-fabricated lead-in bends enable the creation of tensionless wall entries that are bent up to 90 degrees to the piping. To be used with Rauthermex and Rauvitherm pipe. Connect other pipes using the standard I-shroud connection.
Rehau 75mm+75mm/225mm Duo Lead in Bend The Rehau pre-fabricated lead-in bends enable the creation of tensionless wall entries that are bent up to 90 degrees to the piping. To be used with Rauthermex and Rauvitherm pipe. Connect other pipes using the standard I-shroud connection.
Rehau 90mm/160mm Uno Lead in Bend The Rehau pre-fabricated lead-in bends enable the creation of tensionless wall entries that are bent up to 90 degrees to the piping. To be used with Rauthermex and Rauvitherm pipe. Connect other pipes using the standard I-shroud connection.
REHAU CLIP-FLEX I-Large Shroud
REHAU CLIP-FLEX I-Small Shroud
REHAU Everloc 90° Elbow The REHAU Everloc 90° Elbow is specially designed for sharp turns in your underground PEX installation, particularly when bend radii cannot be used or when the route is obstructed. This elbow is ideal for use in REHAU RAUVITHERM and RAUTHERMEX systems, providing a smooth and secure 90-degree turn. Utilising REHAU’s compression…
Rehau EVERLOC™ Compression Sleeve – 40 x 3.7mm The compression sleeve jointing technique is a patented method developed by REHAU for the rapid, safe and permanently leak-tight connection of PE-Xa pipes. It consists simply of a fitting and the compression sleeve. Additional sealing elements are not required, as the pipe itself acts as a seal….
REHAU Everloc Equal Tee The REHAU Everloc Equal Tee is your go-to for branching off from a main pipe run in underground PEX installations. Used for REHAU RAUVITHERM and RAUTHERMEX underground heat main installs, this equal tee is designed for situations where all pipe sizes are equal, ensuring a secure and reliable connection in district…
LoCO₂ Heat has a team of highly knowledgeable in-house engineers with years of experience. We can offer a service ranging from the supply of pre-insulated pipe to a complete package that incorporates sizing, design, drawings, and installation. We can assist as much or as little as you require.
We have worked on many district heating projects in the past, including one of the largest polymer district heating networks in the UK, where over 7km of pre-insulated pipe was used. You can trust us with your project.